headliner replacement

Joined
Sep 7, 2007
RO Number
28513
Messages
63
We tore out our headliner in our forward cabin and glued 1/4" foam up and then glued some marine grade vinyl over that. Well the vinyl fell down. The foam stayed. We noticed the vinyl had a slippery back on it so we're assuming that's why it fell. ( and it took 3 months for it to fall ) What do we do next? We're thinking about removing the foam again and purchasing some headliner material with the foam already attached. ( we really liked the vinyl headliner look ) Our second problem is we used 10 cans of glue at $15 per can. ( twice because we tried to reglue the vinyl, didnt work ) We would like to use the properly glue but where do we get it, what kind is it and how do we apply it? We're thinking about finding someone who has pot sprayer ( for glue ) or maybe using a automotive type spray gun. We need suggestions on the material, glue and how to apply it....dang, you want to do it also? lol. Any suggestions here? any and all suggestions would be appreciated. Tnanks again
 
a) use headliner material with the foam attached. The reason is that a glue which will adhere to the vinyl will also usually destroy the foam. So use the vinyl w/ foam attached.

b) use the glue recommended. Note that this may include "water based contact adhesive". If so it can be purchased and applied with a roller or brush ( roller definitely preferred ). Please be sure to follow the instructions carefully. The stuff can be tempermental. I would not consider using a sprayer. Non-approved glue will can and usually will dissolve the foam...

-edit-

Went back to research...

One brand recommends to -not- use water based contact adhesive.
 
Yeah we used the recommended headliner glue that i bought at an automotive store. It didnt eat up the foam at all, it just slow released the vinyl from the foam. The foam stayed glued to the fiberglass. The brush on glue is a thought though All advice is appreciated.Thanks
 
I replaced my headliner a few years a go. I got the fabric from sailrite.com. (hope that's OK). Get the foam backed stuff and use the recommended adhesive. I think it was #8088 3M spray adhesive. I bought that at Wallmart. It is a huge and very messy job but it turned out very nice. Removing the old foam backing was probably the worst part of the whole deal. I actually sharpened the end of my shop vac nozzle and scraped it off with that. That way the vac sucked up all the residue as it came off the ceiling. There is a number of different glues required, depending on what you are doing, like seams and edges. Sailrite was very helpfull on the whole project.

Good Luck

Jim
 
It sounds as though your problem was one of plasticizer migration. Without getting too technical, when vinyl is made flexible, it is done by using slow drying oils, etc. When you use an adhesive to bond this to another substrate, the adhesive must be resistant to plasticizers or you'll have a failure over time. The bondline will feel like a gummy, sticky mess. In effect, the plasticizers leached their way into the glue and caused it to fail.

As far as an over the counter adhesive recommendation is concerned, I'm not sure if any of the spray can products will meet your needs without doing some more research on my part. The companies which specialize in automotive, RV, marine upholstery use products which are not affected by plasticizers.

As was previously noted, you might be better off buying a foam backed vinyl for your application. That way you do not have to worry about migration problems. However, you need to use an adhesive with high heat resistance to insure long term performance.

As far as product application is concerned, do not try to brush or roll the adhesive onto the substrates. Most of the solvent cements are comprised of 18 to 25% solids and 75 to 80% solvent. If you try to brush or roll these products, the solvents will be drawn into the foam and draw the solids with them. Thereby, starving the bondline of solids and adhesive.

In the long run it might be cheaper for you to utilize a company which does this type of work. They would have the proper adhesive and headliner material. Plus, they would need to furnish a guarantee.

Bob
 
I re-read your original post and had another thought.

If your foam is still securely held in place and the surface is not contaminated (sticky residue) you can buy fabric backed, foam backed or expanded vinyl and use a spray adhesive like 3M #80 rubber and vinyl adhesive. It is resistant to plasticizers and has high heat resistance.

Bob
 
After reading your post i looked up that place and did some thinking...Here's what we got planned so far. We're going to tear down the existing foam ( there is some residue left ) and buy that vinyl headliner that's already got the foam attached to it and get an upholstery place to help spray it. I've already been in contact with one and they dont have a problem with that....I appreciate the lead as to where to buy the proper stuff. thanks again
Harry
 
Back
Top