DepthFinder-replacing

Joeshoes

Member
exMember
Joined
Jan 1, 2000
RO Number
1967
Messages
601
My Depthfinder pulled off over the summer and I need to buy a new one. Old one was a Hummer which I was not crazy about. It hung off the stern.
I would prefer to buy one of those that read through the hull rather than putting a new hole in the boat. The hull is about an inch thick so I do not want to put a hole in it. I only have a Furono GPA so the Finder will stand alone.

I want to spend $ 100 or $ 200.

Good ones? Any experience?
 
Your only problem will be with Depth, You lose power as you sound thru the fiberglass hull. Buying a cheaper unit will only increase problem. If you only need depths to a few hundred feet you should be okay. If you are looking to go deep it wont work as well.
 
Your Pequod is FG , not wood hull right? (Shoot-thru doesn't work with wood.) http://www.boatfix.com/cart2/Scripts/prodList.asp?idCategory=21 If you really don't want to install a flush mount thru hull you can temporarily put a transom mount in a bag filled with water and try various places around the bilge to see if results are satisfactory, then epoxy to the hull or install in an antifreeze-filled PVC tube epoxied to the hull. If you can't find good results with the bag , you can still go back to the transom mounting.
 
I've also been researching this subject since my old depth sounder has become unreliable. I prefer just a digital readout of the depth since I don't have room to mount yet another piece of equipment, I do have a hole in the dash available and I've never run aground with my old one.

I would suggest that you get some advice (like from BoatFix) when ordering. Some manufacturers are a little stingy with the amount of cable they supply with the transducer and almost all use their own proprietary connectors so you can't really make up your own extension. The prices shown in some places often include only a transom mount transducer and not the thru-the-hull one that you need.

If you do mount your new unit's transducer inside the hull, you'll need a faring block to square up the transducer fore and aft and left and right.
 
Many ways to do this. First be sure that you do not have a cored hull. If your hull is cored, you cannot shoot thru the hull (unless you have an area where the core is removed and there is solid glass, or where you can remove the core and make it solid glass (this requires some surgery on the boat--so be sure you are qualified). There is not much loss of depth--I have had a number of shoot thru the hulls, where I have achieve the full depth--up to 1000 feet, if you do a good installation.

Using the baggie full of water is a good idea--but I would not use antifreeze. Consider mineral oil--this is a very good coupling agent and transducers do fine in it. You can use a transom transducer to shoot thru the hull. I am not sure what antifreeze may do to these--it may be OK--but mineral oil has been used for a long time and often used as coupling agent in ultrasonics. I like to make plywood boxes, with epoxy/glass inside and out, glassed to the hull. You would have to rough up the PVC pipe to get it to reliably epoxy to the hull--and also use cloth strips, rather than just epoxy to the hull. A thru hull transducer can suspended from a board cut to fit the top of any tube or box glassed to the hull--but so can a transom mount transducer.

Thru hull transducers can also be epoxied direct to the bottom of the hull. It is better to have the face of the transducer paralled to the surface of the water--and there are several ways to do this.

Hummingbird and Lowrance are the two major players at the low cost end of the specturm. I much prefer a fishfinder over a digital finder (although I have both) I have both Lowrance and Hummingbirds which are black and white and cost about $160. Their performance is about equal. I also have a more expensive color Lowrance--and definately it is a better depth finder. I also have a Garmin--which I do not like as well as the others. The best is probably the Furuno--but you are looking at much higher costs.
 
Thanks for the input guys, yes the hull is Fibreglass Reinforced Plastic that is 35 years old. I just do not want to put another hole in the boat. If I have to I will pay up to $ 500. I do not fish so I do not want a fishfinder.

Models? Boatfix?
 
Airmar makes most of the transducers out there -check out their site.

There is some confusion out there, and some evidenced above, as to the distinction between through-hulls (which are generally taken to be those that need a hole) and in-hulls (which don't).

I tried several ways of doing the in-hull, could not get a reliable reading.

Finally broke down and put the hole in the hull, no big deal. Got the Airmar model that angles the sensor inside the transducer unit so you don't need to angle the unit itself and have it protruding below the hull - this works great.

Good luck.

Orcbait
 
Joe- As the plain fishfinders tend to be relatively low powered as mentioned above you just have to play around with the in-hull shoot-thru to see if you can find a setup that works OK compared to another transom mount. Here's the B/F depthfinder link I thought I was posting above ; http://www.boatfix.com/cart2/Scripts/prodList.asp?idCategory=26 .I'd tend to be a little leery about the cheaper units but heck they are cheap -buy 2. Most don't seem to list power output. Just look for what will fit your dash and which ones have the digits displayed in a manner agreeable to you and have a transducer you'd like to try.

Bob-I just mentioned that 'cause Airmar seems to be switching their coupling agent recommendation to non-tox propylene glycol A/F over mineral oil. http://www.airmartechnology.com/uploads/InstallGuide/17-446-01.pdf I think their may have been some problems with min oil attacking some of the silicone some used to bond their cannisters to the hull. In other Airmar cannister installation pdf's they still say either propylene glycol or mineral oil. Ihave no idea if either would have any detrimental effect on a plastic transom mount type TD .Both liquids normally come in plastic containers but that means little.

Orcbait- That's Airmar's "Tilted Element" thru-hull, which probably isn't normally supplied with most depthfinders but may be a trade-up option in some cases. A very good choice those looking for a thru-hull with very little drag & minimum vulnerability
 
Back
Top