Docking question

camman73

Member
Member
Joined
May 23, 2005
RO Number
17493
Messages
256
How would you have approached this.

Single screw, I/O, 21ft

dock.jpg

Here is what I tried and it didn't work out too well.
I planned to back in at about a 20-30 angle to the
left hand side of the dock, attach a line at the
stern, turn hard left and fwd throttle to bring
the front in. Wind caught my bow before we
could get the rear line on and bow swung over,
would have hit the boat next to us if somoeone
hadn't jumped on and pushed it off.
How would you have done this differently? This
spot and backing in were the only options.
No damage was done except for my ego, always
trying to learn better ways of doing things for
the future.
 
I would have approached well left of the dock, allowing the wind to bring the boat to right side. Fenders deployed to port. This requires a bit of throttle-play to maintain a slow speed and to make corrections. I wouldn't have bothered with the additional crap of being stern in and pivot...bow on, let the wind do the work.
 
if you dont' have any piling between the slips, you have to set fenders before coming in to protect both boats.

what's upwind from the slip ? if the end of a dock, can you pull alongside, port to, bow into the wind, to grab a stern line and a bowline, then pivot the boat in ? with a small boat, that could work out.

otherwise, tie a short line from the piling or cleat at the end of your slip to a midship cleat, kind of between a breast line and a spring line. As you come in, grab the line a tie it amidship, as you back up on it it will keep the boat close to the dock. with an sterndrive, turning the wheel to starboard may help keep the bow closer to the dock

if you have help on board, your crew can ease the line as you back in. otherwise, get on the dock and finish by hand.

springlinein2.gif
 
Thanks for the tips.

Mike, there is a boat on the right side like in Pascals pics, sorry for my sorry attempt at a drawing. If it was open yeah, would have backed in the middle and let the wind push me to the right side.

Pascal, no pilings between boats and the end the left side of that pier had another boat docked with his nose sticking out past the end of the pier. This isn't my permanent dock, just a one time thing, so leaving a rope there was out of the question. Did have a crew so should have had them throw a rope over the piling at the corner of the dock attached midships and use that to keep the bow from swinging out.
Bumpers were out but my bow was about to crash his stern which was much lower.
 
if not your slip, then you need to attach the line, a crew woudl be handy in such a situation but if you can tie your midship cleat to the end of the dock with a short line (breast line) you're not gong to hit the other guy. then you ease the line as you back in, using it as a spring.

this is why midship cleats are important, unfortunatel, many small boats don't even have them !!!
 
I used to have a similar situation with my home slip. There's a rule at our marina that you must keep at least two fenders deployed on the non-finger side of your boat. I'd add three more to my boat, back in and simply rub against my neighbor Joe's boat if I had to with five fenders between us. I warned him ahead of time and he was cool with it, but the truth is, I usually got in before I had to touch. Many times, I'd get into the slip, jump off and the boat would be gently blown into his so I'd have to pull it back with the lines. Once in a while I would actually use his boat as leverage.

Some thought I was nuts for actually using my fenders but I said hey, I'm boating today, you aren't :)
 
http://spot.pcc.edu/~mtrigobo/docksim/index.html Is a docking simulator, you can set wind, current, etc.
It gives ya an idea of how a boat can respond to wind and currents of different speeds.
{some people have way to much time on their hands ;)}
 
I used to have exactly that situation almost every time I returned to my home slip when I owned an express cruiser. To make matters worse, I had no choice but approach from upwind as well. The wind pushes the bow of those boats around so much it was very very difficult to back in.

When backing in, I could never get the spring line onto the port side, and couldn't get the boat lined up -- the bow would just not come around into the wind. Invariably I had to fend off the other boat and kind of walk the boat into the slip. That's not necessarily a problem, but in the end I gave up and started docking bow in. That was much easier, because from the helm I could pick up the spring at the end of the finger, drop it on my starboard midship cleat, and drive in. The spring kept the bow close, and I could control the stern from the helm. Sometimes it's just not worth the trouble to back in.
 
I can't back our I/O deckboat very well at all at slower speeds. Turn the helm full in either direction and not much, if anything, happens at all. The boat still backs up in a straight line.
 
quote:


this is why midship cleats are important, unfortunatel, many small boats don't even have them !!!






Yeah, no midship cleats on this 21ft. Might be a worthwhile project to add some. From what I'm getting from the posts here best option is to try to get the midship cleat on, if that's not possible be prepared to do a little rubbing with the boat next to you. Might have to get a few more bumpers.

Thanks for the input.
 
yeah, mid ship cleats come in very handy in some situations... decent fenders are a must have too although storage is a problem on a small boat.
 
Lacking a midship cleat I think you could do almost the same thing with a long spring to a bow cleat; but you'd have to have someone to shorten it up as you backed in. If the bow starts to fall off snub the line and go ahead on it to pull the bow in. Then back down/shorten up some more. Eventually it would become a bow line.

I'd cheat; I'd go in bow first with a spring and worry about turning the boat around when conditions were better.
 
Why did you have to back in?

What kind of crew did you have on board?

A 21 foot I/O isn't so heavy so moving it around by hand is often the best approach. If I had at least one able bodied crewman on board I would have brought the boat broadside to the slip, bow into the wind, turn the stern in then shut the engine off. You and the crew fend off the boat already there and pull yours into the slip.

So, basically, just like you did it but announce it as the plan ahead of time so your ego isn't damaged.

Rod
 
If you have a decent wind across the boat, forget the bit about going in slowly..go in reasonably quick and hit forward as soon as you are near where you want to be..amazing how quick they stop. Use reverse if driving bow in to stop you...line the boat up and go for it..the wind will get you most times if you go in slowly...and when reversing..do not look over your shoulder..turn around and face where you are going...use your hands behind your back to control the boat...gives you far better vision that way.
 
abdiver, backing in isn't required, just ending up that way eventually is. It would be possible to spin the boat around by hand at a later time. At the time I thought backing in wouldn't be too bad. I was just looking for tips that would help next time. Then depending on the situation I can make the decision to try some of the things mentioned above or to bring her in nose first and deal with turning her around by hand.
 
if you can bring the boat bow in, it will be easier in this situation since you have better control of the stern with the drive. Then you can use a spring line tied to your bow cleat which once set allows you to forward on the line and keep the boat gainst the dock. As jockey said, dont' go too slow so that you minimize the time you're vulnerable to the wind.
 
Pascal's second picture. Pivot in on the spring, it'll bring you up neat. Of course, if you don't have a piling or something to make that line to - well, then, that idea's out the window...

"If you have a decent wind across the boat, forget the bit about going in slowly..go in reasonably quick and hit forward as soon as you are near where you want to be..amazing how quick they stop. Use reverse if driving bow in to stop you...line the boat up and go for it..the wind will get you most times if you go in slowly...and when reversing..do not look over your shoulder..turn around and face where you are going...use your hands behind your back to control the boat...gives you far better vision that way."

Ehhhh...'kay....
 
I have a twin inboard 36 ft., I would have not tried that without help. I can make the boat "walk and talk" but there are just things you can't do. I like the fact you used a spring line, that says you have an understanding. Good try.
 
quote:

Originally posted by JimPend

I have a twin inboard 36 ft., I would have not tried that without help. I can make the boat "walk and talk" but there are just things you can't do. I like the fact you used a spring line, that says you have an understanding. Good try.






Holy crap! Did Jim just post something positive? Somebody mark the calendar![:-bigeyes]:D
 
No kidding, Brian....right after I called him out on another negative one in another post!
 
Back
Top