how should i repaint this bottom?

reimelss

Member
Joined
Nov 28, 2007
RO Number
29033
Messages
27
Ok...this is my first boat. The bottom needs to be repainted, I am pretty sure the previous owner used AF paint because it is/was flaking off. I pressure washed most of it off...It also had a lot of growth on it and the barnicles seem to be in there pretty deep...I don't want to scrape to hard or damage anything untill i know what I am doing. Some of the old paint isnt coming off easy either? will I need to strip or sand and start fresh? do i paint over the old? not sure what to do. here are somepics...can someone point me in the right direction? thank you.
http://www.ellisawesomeworld.com/images/boat/
 
You can paint over the old paint IF it's well adhered. The rest looks like a job for a sander.
 
I would have it media blasted and start from scratch. Coat it with a barrier coat, repaint in your choice of color, and from the looks of the first pic, you need to raise the waterlilne a little bit
 
If its "flaking off" it may not be an ablative but rather a hard paint. If you rub a cloth across the paint and it rubs off (like a fine dust) its likely ablative. If not, its probably a hard paint. You can paint either an ablative or a hard paint over well adhered hard paint but you cannot apply a hard paint over an ablative. Like others said, if it is flaking off you'll need to do some careful sanding to remove any loose paint.
 
It looks as if the chines have kissed the bottom. Those need to be repaired as well.

How big is the boat and is it an outboard.

The reason I ask, it is much easier to flip the boat upside down and work standing up than it is to work on your back. BTDT. It appears the hull has been painted in the past. Do you intend to attack that as well?
 
"How much does sandblasting a boat go for?"

You want to sodablast, not sandblast. Trailerbale boat, brought to a shop, should run you $20-$25/foot, plus a blocking fee and a possible disposal fee. For your boat, I would guess ~$1K.
 
Is there any other stripping method you would recommend? and type of chemicals?
 
There are chemical strippers you can use (BIX, Soystrip, Peel Away etc.) but I have not personally used them. You could go the old fashioned way of Tyvek suit, respirator, and sand paper - lots of sand paper.

If using a chemical, be sure to read all instructions (for example BIX makes a product that specifically is NOT to be used on fiberglass) and follow them. Also, beware of any possible environmental issues.

Is your boat at a boatyard? They may have rules against the use of chemical strippers.

I personally hate dealing with bottom paint and would simply pay the man to have it stripped.
 
A sharp 2" wood chisel would make for easy removal. Just stay away from any radii as it will gouge those areas. Use a rounded painters scraping tool for those area. It’ll still be a dirty job no matter what method you use. Years ago I did my 28 footer in a week end using that method but I was a lot younger back then.
 
Are you keeping the boat in the water all season or trailering? If in water, the blasting, apply barrier coat, and paint is the way to go. If trailering you may not want to go through all that trouble. If you don't want to get crazy for your first season, knock the loose stuff off & throw on a coat of new and you'll be good for a season or so. Any decent Interlux or Petit paint will typically adhere to the old. Barrier coating adds additional protection against blistering and if you have it blasted you may end up with some areas that need to be repaired - not a real big deal, just takes a little time. Interlux's website has all kinds of info. I tried the chemical stripping route a couple years back and finally surrendered and had the yard sand blast it clean (if it is someone that does only boats, they can use sand - if they're not careful you can end up with more problems then when you started). GOOD LUCK and welcome to boating!!
 
Thats what i was planning on doing...paint it this year and blast it and barrier coat it next season
 
quote:

Originally posted by reimelss

Thats what i was planning on doing...paint it this year and blast it and barrier coat it next season






If that's the case, follow BobJ's advice. BUT... be prepared to do extensive bottom work to get it right. No different if you did it this year. It's just another year's growth. If you use it this year and are truly committed to getting it right, pull early in the fall and commit a few dollars to some pro work and a lot of sweat equity for the rest, and you may just convert a piece of carbon to a diamond.

WRT blasting, ITK is spot on about the price. I have a 33 and I am looking at ~1200 to go to bare glass.

The bow entry looks like a Formula I used to drive. Am I close?
 
i had a similar situation. first, i tried to sand it off with a random orbital sander. don't try this as the dust is so fine, it'll find it's way into everything (even a respirator and tyvek suit). finally, i used one of the chemical peels. it really loosens the paint, but you'll still need to scrape it like crazy with a scraper. when you're finished, you should paint the bottom first with a barrier coat. it's a 2 part paint/epoxy mix that seals the bottom completely. then use some ablative antifouling paint of a different color. the ablative paint will wear off while the boat is underway and will expose the different color barrier coat at the end of the season. you'll still need to powerwash, but you won't need to scrape before applying more ablative paint. issues here are the enormous effort to get the bottom scraped the first time (mine took a solid 20 hours of work) and the cost of ablative paint (which is not cheap).
 
ok...so my plan is to scrape off the paint i can...and repaint this year and next season have someone soda blast it and start from scratch...do i need to apply a barrier coat to the bottom if i am going to start from scratch next year? the growth i have now is only on the sides near the water line...can i sand/scrape that down and repaint...i have no growth on the bottom...the previous owner said the boat is very solid and does not take on water...i still haven't paid the balance on the boat...if the boat does take on water, then i always have that to fall back on and be able to absorb some of the cost
 
Ok...I'm in the same position here. have a boat i bought at the end of the season..Old paint is 1/2 on 1/2 off..at least 4 layers!! Starting to scrape now. Once I get it down to nothing, I should apply a barrier coat?? Any particular type/brand? Then once it dries I apply bottom paint correct?? Type/Brand??

Thanks for any help you guys can give me..

Mike
 
Once the old paint is off and you are down to gelcoat, 4-5 coats of Interprotect 2000 then whatever anti-fouling paint you like.
 
Back
Top