Slip Width

mixman

Livin' the life.
Member
Joined
Feb 28, 2007
RO Number
25362
Messages
3,996
We've got a chance to move to a better slip at our marina. While longer than our current slip, the new slip is actually cheaper. The reason is the width of the slip, or lack thereof. Our current slip is 16' wide. The new slip is 12' 6" wide. Our boat has a beam of 9' 6". I've got no problem getting the boat in and out, but extremes of weather concern me, as well as extremes of tides. We currently keep the boat centered, so we've got over 3' on either side. We'd be cutting this amount in half with the new slip. Any opinions if a foot and a half on each side is adequate?
(normal tidal departures are around 18", with extremes of a few feet)
 
Should be fine. Just make sure you pay attention to the lines the first few times you tie her up.
 
If you have a finger on either side, as compared to a finger and a slipmate, you should be ok. Good fenders are obviously a must.
 
That's alot of room for that size boat, some marinas your lucky to have a foot in between each boat. You should have no problem.
 
There's a finger pier on one side and 3 pilings on the other between us and the next slip.

Perhaps I've just been spoiled by 4 years in a 16' wide slip. I've done plenty of overnights in skinny slips, but I'm used to having the extra room (and extra length of lines) for all the "storage" time.
 
it really depends on how exposed the slip is and how big are your tides. If exposed to wind/chop, you want a couple of feet on each side, less than that and the boat will hit the pilings. not a big deal, your rub rail should handle that, but it's not ideal.

Fenders never stay in place, or you have to use fenderboards, which increase the amount of time it takes to get underway.

I have about 1 1/2 ft on each side, both in my own slip and also for Charmer, and the lines have to be just right. yet if it blows, the boats do touch the pilings.

All depends on how much nicer the new slip is...
 
I'd do it. Tide slides or a mooring ring (http://www.moor-ring.com/index.html) or similar will do well.
 
Mix, that is about what we have, and I use some fenders on the finger side tied to the finger and nail on pileing strips on the others. I like the fabric, foam filled 4" style.
 
I'd do it.
Just use big enough fenders. If your worried about them moving use the the inflatable kind with the girdle that reshapes them into a V with a piling hugging notch in them. Or perhaps the long flat inflatable type. They tend to stay in place very well too.
And as mentioned, fender boards would work well also.
Shouldn't be that big a deal to take them in or hang them up when you go to leave. Just be aware, in a good blow, those pilings may bend and allow to to get closer to the dock.
 
We don't have tides in South Dakota, but heavy south winds that run at 90 degrees to our slip, we're 14'3" beam in a 16 and no problems, but we are bow first always, and on those windy days use the rub rail frequently... Only mishap was a day when she was about 30mph from the south and had to come in hot, did not damage the boat but bent the metal pole pretty good, and of course all in front of a large audience : (
 
I'm 15' beam in a 16' beam slip. Yup you were spoiled. Do it and save the money.
 
To give a better idea. Here's the general area off the Chesapeake (which is to the east):

myc1.jpg


This is the marina a little closer. Notice the main fetch area is to the west. Green indicates our old/current slip. Red indicates the new one.

myc2.jpg


Here's our old slip, where we'd get some slap-back from the bulkheads if weather was coming from the west.

myc3.jpg


And here's the possible new slip. Again, going from 16' width to 12' 6", but notice it's better protected (no bulkheads, just a tiny beach to absorb waves):

myc4.jpg


Note: we could move out 2 more slips and have a 13' 9" wide slip, but that would be $300 more per year. Originally, that's what we were going to do, but from the comments above, I don't think the money is justified.
 
yep, better protection, it should be fine... if you adjust the lines right, you may not need fenders.
 
I used to have our 38 footer in a slip with less than 2" on each side. Yes that's inches, not feet. People used to walk down the dock and look at the boat/slip and shake their heads in disbelief. Normal tidal change is in the 3 foot range.
 
With careful rigging of spring lines and crossed stern lines a "skinny" slip is not really a problem. Dock mounted fenders, fender boards etc may be needed. But frankly, what you describe is what most of us have kept our boats in, most of the time. Dock space is precious, and dockmasters want to cram as many "boat-feet" of boats in there as they can.

Besides, it makes it easier to borrow tools from the neighbors... ;)
 
Kurt floating docks or fixed? If floating why not use fixed donuts circular fixed to the dock (wheels) on heavy steel angle with a post? If your not on a floating dock forget that idea. I love my spot, parallel to the main dock at the end all the fingers are to my port side and floating. I'm spoiled I have the best slip in the marina 50' long and 45 feet to the marsh. Spinning the boat can be fun at low tide but the bow thruster really helps there.
Bill
 
Thanks all for the responses. I guess, as I've said before, I've been spoiled by having a slip almost twice as wide as my boat.

Bill - fixed docks here. The upside is nice, forgiving forward wood pilings to pivot on when the need arises :-)

Pascal - Thanks for the input. I'm not one for fenders if they're not needed, and I hope to get away without them in this slip. As you said above, they're pretty useless in a fixed slip with tidal changes anyway.
 
Cake walk. Google Med Mooring and see how much room is needed to slip a boat. Use the savings to buy more fuel.

The beach should break the current and waves better than a break wall.
 
I use to have a simular set up and now I have a 16' slip. We spend a lot of nights in the slip and during windy nights the boat would hit the pilings and wake me up. In the wider slip that never happens. It is very difficult to get the proper rigging and bumper compo to keep the boat from hitting during a good blow.Both slips are in very protected water and wave action was never a factor. I like a good nights sleep.
 
Back
Top